FLUKE MICROSCANNER2 MANUAL PDF
get started using the tester. For additional information, see the MicroScanner2 Cable Verifier. Users Manual on the Fluke Networks website. Safety. Warning. MicroScanner2 Cable Verifier. Accessing the Users Manual. This guide provides basic information to help you get started using the tester. For additional. View and Download Fluke MicroScanner 2 user manual online. Cable Verifier. MicroScanner 2 Test Equipment pdf manual download.
|Published (Last):||9 January 2013|
|PDF File Size:||9.81 Mb|
|ePub File Size:||8.9 Mb|
|Price:||Free* [*Free Regsitration Required]|
Fluke MicroScanner 2 User Manual
Page 34 – Connecting to Telephone Networks Wired i The analog toner has four songs. Do not put in sunlight. Integrity Networks Alaska Branch. If exposure to chemicals appear. Connect the tester to the cable. Don’t have an account? The wiremap is drawn with proportional length to visually indicate the approximate location of faults. The digital IntelliTone signal is mjcroscanner2 to detect at a distance than analog tones, and its frequency and encoding eliminate cable misidentification due to signal bleed and radiated or ambient noise.
The display shows a scrolling sinewave in analog toner mode 2. Architects, Consultants and Designers.
MicroScanner2 Getting Started Guide, Rev. 1 | Fluke Networks
Comments to this Manuals Your Mankal. Page 59 Index testing —R— coaxial cabling, 28 registration, 1 twisted pair cabling, 11 remote ID locator, 10, 22 toner, 32 replacement parts, 42 analog mode, 35 RJ11 jack, 10 IntelliTone mode, 32 SmartTone function, flukke, 36 —S— troubleshooting safety information, 3, 39 cabling faults, 47 serial number, 41 the tester, Use the probe to search for the cable.
Welcome to Fluke Networks. If Table 2 does not help you solve a problem with the tester, contact Fluke Networks for additional help. Regulatory Information MicroScanner Cable Verifier Users Manual Regulatory Information This microscqnner2 generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the manual, may cause interference to radio communications.
Toning in IntelliTone™ Mode – MicroScanner2
Notes If you cannot locate the IntelliTone signal on 2-conductor cables, the cable may be shorted. Using The Toner Refer to Figures 24 and All product names are trademarks of their respective companies. SmartTone works with the IntelliTone probe and with analog probes. Detection of crossed pairs requires a far-end adapter.
Index cable tests Symbols coaxial cabling, 28 “? Split Pair Wires connected to wrong pins at connector or punchdown Open block. Versiv Cabling Certification System. It has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15, Subpart J of the FCC rules, which are designed to provide reasonable protection against such interference This can occur if the port does not The tester can detect active and inactive Ethernet ports, as produce reflections.
Fluke Networks warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media. Without this termination, the tester cannot detect crossed wires or crossed pairs. The higher the number, the stronger the signal. The display shows the song number 3. For the latest list of options and accessories visit the Fluke Networks website at www.
MicroScanner Cable Verifier Users Manual The tester cannot measure length past the bridge tap Connecting to Telephone Networks Wired in because reflections from the bridge tap connections Star Topologies interfere with measurements.
FLUKE MICROSCANNER 2 USER MANUAL Pdf Download.
Page of 60 Go. Punch Down Tools and Termination Tools. Use the probe to manuql the tone source in the cable bundle or at the patch panel.
Category 8 Cable Testing. Using microzcanner2 Toner You can use the tester with microscannfr2 optional tone probe to locate cables in bundles, at patch panels, or behind walls. Using the Toner in IntelliTone Mode For cabling not terminated with an F-connector, use an adapter or hybrid patch cord to connect to the cabling. Page 33 – Connecting to a Telephone Network Wired Open on Coaxial Cabling egk Use the tester to check for shorts.
Using the Toner in IntelliTone Mode.
Fiber Inspection and Cleaning. Press PORT to select twisted pair or coaxial cable. MicroScanner Cable Verifier Users Manual split pair, 15 telephone voltages, 16 —U— universal adapter, 10 —V— version information, 41 voltage detection, 5, 16 —W— wiremap adapter, This crossed pair is likely caused by mixing A and B cabling.
See pages 11 and Connect the tester and probe to the cabling as shown in Figure 4. Locations of the tester and wiremap adapter may be swapped. Fluke Networks does not warrant that software will be error free or operate without interruption.
Table of Contents Mifroscanner2 to my manuals Add. To print the manual completely, please, download it. Connect the tester to the cable. This equipment is intended for Fluke Networks. Use the tester to check for shorts.